Servo frame "JR Type 11" is as thin as
the servo itself and keeps it precisely in position. The
frame is fixed in the wing with epoxy while two screws
hold the servo in the frame. Two close-fitting red
pieces connect servo and frame.
The system makes linkages possible which are free from
play but also allows to replace a damaged servo within
seconds.
Technical Data:
outer dimensions: 36 x 25 x 11 mm (1.41"x0.98"x0.43")
weight: ca. 2 grams
The following servos fit frame Type 11:
GR/JR C 261, C 121 und DS281
Price:
6.25U$ea. |
 |
Servo frame "JR Type 13" is as thin as
the servo itself and keeps it precisely in position. The
frame is fixed in the wing with epoxy while two screws
hold the servo in the frame. Two close-fitting red
pieces connect servo and frame.
The system makes linkages possible which are free from
play but also allows to replace a damaged servo within
seconds.
Technical Data:
outer dimensions: 45 x 35 x 13 mm (1.75"x1.38"x0.51")
weight: ca. 4 grams
The following servos fit frame Type 13:GR/JR C 341,
DS361, DS368, DS3068
Price:
6.25U$ea. |
 |
Servo frame "JR Type 19" is as thin as
the servo itself and keeps it precisely in position. The
frame is fixed in the wing with epoxy while four screws
hold the servo in the frame. Two close-fitting green
pieces connect servo and frame.
The system makes linkages possible which are free from
play but also allows to replace a damaged servo within
seconds.
Technical Data:
outer dimensions: 45 x 35 x 13 mm (1.75"x1.38"x0.51")
weight: ca. 4 grams
The following servos fit frame Type 19:
GR/JR C4621, C4421, C4451, C4835, C4855, C4821, C5177, DS8025, DS8041, DS8231, DS8411, DS8417, DS8418, DS8700G, DS5391, DS5491 und DS8311
Price:
6.25U$ea. |
 |
Servo frame "JR Type 11B" is
as thin as the servo itself and keeps it precisely in
position. The frame is fixed in the wing with epoxy
while two screws hold the servo in the frame. Two
close-fitting red pieces connect servo and frame. The
system makes linkages possible which are free from play
but also allows to replace a damaged servo within
seconds. Please note that the frame should be glued into
the wing while a servo is installed in the frame. This
is to ensure the frame doesn´t bend during installation.
Technical Data:
outer dimensions: 52 x 38 x 9 millimeter
that is 2 x 1.5 x 0.35 Inch
weight: ca. 3 grams
The following servos fit our frame Type 11 B:
Graupner DS 3288, JR378 and JR
DS 171
Price:
6.25U$ea. |
 |
Servo frame "Type ATX" is as thin
as the servo itself and keeps it precisely in position.
The frame is fixed in the wing with epoxy while two
screws hold the servo in the frame. Two close-fitting
red pieces connect servo and frame.
The system makes linkages possible which are free from
play but also allows to replace a damaged servo within
seconds.
Technical Data:
outer dimensions: 47 x 36 x 12 millimeter
that is 1.85 x 1.42 x 0.47 Inch
weight: ca. 4 grams
The following servos fit our frame Type ATX:
Airtronics 94761
Price:
6.25U$ea. |
 |
Servo frame Hitec type 11. The
servo is screwed into the servo-mount which is fixed in
the wing with epoxy. The precise installation of the
servo allows you to build linkages that are free from
play. In case of a damage the servo can be replaced
within seconds.
Technical Data:
outer dimensions: 45 x 35 x 13 mm (1.75"x1.38"x0.51")
weight: ca. 4 grams
The following servos fit frame Type Hitec 11:HS-125, HS-5125
and DS3210
Price:
5.00U$ea. |
 |
Servo frame "Type Hitec 13" is as thin
as the servo itself and keeps it precisely in position.
The frame is fixed in the wing with epoxy while two
screws hold the servo in the frame. Two close-fitting
white pieces connect servo and frame.
The system makes linkages possible which are free from
play but also allows to replace a damaged servo within
seconds.
Technical Data:
outer dimensions: 47 x 37 x 13 mm (1.85"x1.45x0.51)
weight: ca. 4 grams
The following servos fit frame Type Hitec 13: HS85BB and HS85MG
Price:
6.25U$ea. |
 |
Servo frame "Type
Futaba 8" is as thin
as the servo itself and keeps it precisely in position.
The frame is fixed in the wing with epoxy while two
screws hold the servo in the frame. Two close-fitting
adaptor pieces that come with the servo connect servo
and frame.
The system makes linkages possible which are free from
play but it also allows to replace a damaged servo
within seconds.
Technical Data:
outer dimensions: 36 x 25 x 8 mm (1.41x0.98"x0.315")
weight: ca. 2 grams
The following servos fit frame Type Futaba 8:Dymond D4.7,
TS-1002
Price:
5.00U$ea. |
 |
Servo frame "Type
Futaba 9" is as thin
as the servo itself and keeps it precisely in position.
The frame is fixed in the wing with epoxy while two
screws hold the servo in the frame. Two close-fitting
adaptor pieces that come with the servo connect servo
and frame.
The system makes linkages possible which are free from
play but it also allows to replace a damaged servo
within seconds.
Technical Data:
outer dimensions: 42 x 32 x 9 mm (1.65"x1.26"x0.35")
weight: ca. 2 grams
The following servos fit frame Type Futaba 9: Dymond D60,
TS-1014
Price:
5.00U$ea. |
 |
Servo frame "Type Futaba 11"
is
as thin as the servo itself and keeps it precisely in
position. The frame is fixed in the wing with epoxy
while two screws hold the servo in the frame. Two
close-fitting purple pieces connect servo and frame.
The system makes linkages possible which are free from
play but it also allows to replace a damaged servo
within seconds.
Technical Data:
outer dimensions: 47 x 36 x 11 mm(1.85"x1.41"x0.43")
weight: ca. 4 grams
The following servos fit frame Type Futaba 11: S3150, S3155,HS81, HS82 (with
rework)
Price:
6.25U$ea. |
 |
| Wing removal tool. Who never
encountered difficulties removing the wing from the
fuselage or center panel, because the fit is too tight.
Now with the wing tool, wing panel and wing removal are
made easy, also suitable for tail assemblies. Price:
2.75U$ea. |
 |
Suited for DS-, Speed-, F3b- und
F3j-glider, we offer here a
ball bearing support
assembly to
strengthen the S 3150 und S 3155 output shaft. The
additional bearing assembly is simply glued in place
with the servo and deserves the ability to absorb any
effort transmitted to the servo toward the airframe
structure. If used with a servo frame Type 11 it can
easily be disassembled. Installation is made easy with
some epoxy.
This ball bearing assembly is also suited with servo
frames of other types, like for DS 368 or Airtronics
94761, the installation just needs to shimmed by 1mm.
The whole assembly is not taller the the servo itself.
Price:
22.00U$ea. |
 |
Antennas
of 2.4 GHz receivers have to be installed
outside the fuselage when it is built with carbon fibre.
During transportation, ground handling and landing the
antennas get bent or (worst case) buckled. Our wrappers
protect the antennas from getting damaged.
Price is for one bag containing
two pieces antenna wrappers
Price: 9.25 U$ |
 |
| |
|
